Initial commit of Arduino libraries

RadioLib/examples/STM32WLx/STM32WLx_Transmit_Blocking/STM32WLx_Transmit_Blocking.ino

@@ -0,0 +1,119 @@
+/*
+  RadioLib STM32WLx Blocking Transmit Example
+
+  This example transmits packets using STM32WL MCU with integrated
+  (SX126x) LoRa radio.
+
+  Each packet contains up to 256 bytes of data, in the form of:
+  - Arduino String
+  - null-terminated char array (C-string)
+  - arbitrary binary data (byte array)
+  
+  This example assumes Nucleo WL55JC1 is used. For other Nucleo boards
+  or standalone STM32WL, some configuration such as TCXO voltage and
+  RF switch control may have to be adjusted.
+
+  Using blocking transmit is not recommended, as it will lead
+  to inefficient use of processor time!
+  Instead, interrupt transmit is recommended.
+
+  For default module settings, see the wiki page
+  https://github.com/jgromes/RadioLib/wiki/Default-configuration#sx126x---lora-modem
+
+  For full API reference, see the GitHub Pages
+  https://jgromes.github.io/RadioLib/
+*/
+
+// include the library
+#include <RadioLib.h>
+
+// no need to configure pins, signals are routed to the radio internally
+STM32WLx radio = new STM32WLx_Module();
+
+// set RF switch configuration for Nucleo WL55JC1
+// NOTE: other boards may be different!
+//       Some boards may not have either LP or HP.
+//       For those, do not set the LP/HP entry in the table.
+static const uint32_t rfswitch_pins[] =
+                         {PC3,  PC4,  PC5, RADIOLIB_NC, RADIOLIB_NC};
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+  {STM32WLx::MODE_IDLE,  {LOW,  LOW,  LOW}},
+  {STM32WLx::MODE_RX,    {HIGH, HIGH, LOW}},
+  {STM32WLx::MODE_TX_LP, {HIGH, HIGH, HIGH}},
+  {STM32WLx::MODE_TX_HP, {HIGH, LOW,  HIGH}},
+  END_OF_MODE_TABLE,
+};
+
+void setup() {
+  Serial.begin(9600);
+
+  // set RF switch control configuration
+  // this has to be done prior to calling begin()
+  radio.setRfSwitchTable(rfswitch_pins, rfswitch_table);
+
+  // initialize STM32WL with default settings, except frequency
+  Serial.print(F("[STM32WL] Initializing ... "));
+  int state = radio.begin(868.0);
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("success!"));
+  } else {
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+
+  // set appropriate TCXO voltage for Nucleo WL55JC1
+  state = radio.setTCXO(1.7);
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("success!"));
+  } else {
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+}
+
+// counter to keep track of transmitted packets
+int count = 0;
+
+void loop() {
+  Serial.print(F("[STM32WL] Transmitting packet ... "));
+
+  // you can transmit C-string or Arduino string up to
+  // 256 characters long
+  String str = "Hello World! #" + String(count++);
+  int state = radio.transmit(str);
+
+  // you can also transmit byte array up to 256 bytes long
+  /*
+    byte byteArr[] = {0x01, 0x23, 0x45, 0x56, 0x78, 0xAB, 0xCD, 0xEF};
+    int state = radio.transmit(byteArr, 8);
+  */
+
+  if (state == RADIOLIB_ERR_NONE) {
+    // the packet was successfully transmitted
+    Serial.println(F("success!"));
+
+    // print measured data rate
+    Serial.print(F("[STM32WL] Datarate:\t"));
+    Serial.print(radio.getDataRate());
+    Serial.println(F(" bps"));
+
+  } else if (state == RADIOLIB_ERR_PACKET_TOO_LONG) {
+    // the supplied packet was longer than 256 bytes
+    Serial.println(F("too long!"));
+
+  } else if (state == RADIOLIB_ERR_TX_TIMEOUT) {
+    // timeout occured while transmitting packet
+    Serial.println(F("timeout!"));
+
+  } else {
+    // some other error occurred
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+
+  }
+
+  // wait for a second before transmitting again
+  delay(1000);
+}