Initial commit of Arduino libraries

RadioLib/examples/LR11x0/LR11x0_LR_FHSS_Modem/LR11x0_LR_FHSS_Modem.ino

@@ -0,0 +1,96 @@
+/*
+  RadioLib LR11x0 LR-FHSS Modem Example
+
+  This example shows how to use LR-FHSS modem in LR11x0 chips.
+  This modem can only transmit data, and is not able to receive.
+
+  NOTE: The sketch below is just a guide on how to use
+        LR-FHSS modem, so this code should not be run directly!
+        Instead, modify the other examples to use LR-FHSS
+        modem and use the appropriate configuration
+        methods.
+
+  For default module settings, see the wiki page
+  https://github.com/jgromes/RadioLib/wiki/Default-configuration#lr11x0---lr-fhss-modem
+
+  For full API reference, see the GitHub Pages
+  https://jgromes.github.io/RadioLib/
+*/
+
+// include the library
+#include <RadioLib.h>
+
+// LR1110 has the following connections:
+// NSS pin:   10
+// IRQ pin:   2
+// NRST pin:  3
+// BUSY pin:  9
+LR1110 radio = new Module(10, 2, 3, 9);
+
+// or detect the pinout automatically using RadioBoards
+// https://github.com/radiolib-org/RadioBoards
+/*
+#define RADIO_BOARD_AUTO
+#include <RadioBoards.h>
+Radio radio = new RadioModule();
+*/
+
+void setup() {
+  Serial.begin(9600);
+
+  // initialize LR1110 with default settings
+  Serial.print(F("[LR1110] Initializing ... "));
+  int state = radio.beginLRFHSS();
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("success!"));
+  } else {
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+
+  // if needed, you can switch between any of the modems
+  //
+  // radio.begin()       start LoRa modem (and disable LR-FHSS)
+  // radio.beginLRFHSS() start LR-FHSS modem (and disable LoRa)
+
+  // the following settings can also
+  // be modified at run-time
+  state = radio.setFrequency(433.5);
+  state = radio.setLrFhssConfig(RADIOLIB_LR11X0_LR_FHSS_BW_1523_4,  // bandwidth
+                                RADIOLIB_LR11X0_LR_FHSS_CR_1_2,     // coding rate
+                                3,                                  // header count
+                                0x13A);                             // hopping sequence seed
+  state = radio.setOutputPower(10.0);
+  uint8_t syncWord[] = {0x01, 0x23, 0x45, 0x67};
+  state = radio.setSyncWord(syncWord, 4);
+  if (state != RADIOLIB_ERR_NONE) {
+    Serial.print(F("Unable to set configuration, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+
+  #warning "This sketch is just an API guide! Read the note at line 6."
+}
+
+void loop() {
+  // LR-FHSS modem can only transmit!
+  // transmit LR-FHSS packet
+  int state = radio.transmit("Hello World!");
+  /*
+    byte byteArr[] = {0x01, 0x23, 0x45, 0x67,
+                      0x89, 0xAB, 0xCD, 0xEF};
+    int state = radio.transmit(byteArr, 8);
+  */
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("[LR1110] Packet transmitted successfully!"));
+  } else if (state == RADIOLIB_ERR_PACKET_TOO_LONG) {
+    Serial.println(F("[LR1110] Packet too long!"));
+  } else if (state == RADIOLIB_ERR_TX_TIMEOUT) {
+    Serial.println(F("[LR1110] Timed out while transmitting!"));
+  } else {
+    Serial.println(F("[LR1110] Failed to transmit packet, code "));
+    Serial.println(state);
+  }
+
+}