Initial commit of Arduino libraries

RadioLib/examples/LR11x0/LR11x0_Channel_Activity_Detection_Blocking/LR11x0_Channel_Activity_Detection_Blocking.ino

@@ -0,0 +1,106 @@
+/*
+  RadioLib LR11x0 Blocking Channel Activity Detection Example
+
+  This example uses LR1110 to scan the current LoRa
+  channel and detect ongoing LoRa transmissions.
+  Unlike SX127x CAD, LR11x0 can detect any part
+  of LoRa transmission, not just the preamble.
+
+  Other modules from LR11x0 family can also be used.
+  
+  This example assumes Seeed Studio Wio WM1110 is used.
+  For other LR11x0 modules, some configuration such as
+  RF switch control may have to be adjusted.
+
+  Using blocking CAD is not recommended, as it will lead
+  to significant amount of timeouts, inefficient use of processor
+  time and can some miss packets!
+  Instead, interrupt CAD is recommended.
+
+  For default module settings, see the wiki page
+  https://github.com/jgromes/RadioLib/wiki/Default-configuration#lr11x0---lora-modem
+
+  For full API reference, see the GitHub Pages
+  https://jgromes.github.io/RadioLib/
+*/
+
+// include the library
+#include <RadioLib.h>
+
+// LR1110 has the following connections:
+// NSS pin:   10
+// IRQ pin:   2
+// NRST pin:  3
+// BUSY pin:  9
+LR1110 radio = new Module(10, 2, 3, 9);
+
+// or detect the pinout automatically using RadioBoards
+// https://github.com/radiolib-org/RadioBoards
+/*
+#define RADIO_BOARD_AUTO
+#include <RadioBoards.h>
+Radio radio = new RadioModule();
+*/
+
+// set RF switch configuration for Wio WM1110
+// Wio WM1110 uses DIO5 and DIO6 for RF switching
+// NOTE: other boards may be different!
+static const uint32_t rfswitch_dio_pins[] = { 
+  RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
+  RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
+};
+
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+  // mode                  DIO5  DIO6 
+  { LR11x0::MODE_STBY,   { LOW,  LOW  } },
+  { LR11x0::MODE_RX,     { HIGH, LOW  } },
+  { LR11x0::MODE_TX,     { HIGH, HIGH } },
+  { LR11x0::MODE_TX_HP,  { LOW,  HIGH } },
+  { LR11x0::MODE_TX_HF,  { LOW,  LOW  } },
+  { LR11x0::MODE_GNSS,   { LOW,  LOW  } },
+  { LR11x0::MODE_WIFI,   { LOW,  LOW  } },
+  END_OF_MODE_TABLE,
+};
+
+void setup() {
+  Serial.begin(9600);
+
+  // initialize LR1110 with default settings
+  Serial.print(F("[LR1110] Initializing ... "));
+  int state = radio.begin();
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("success!"));
+  } else {
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+
+  // set RF switch control configuration
+  radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);
+}
+
+void loop() {
+  Serial.print(F("[LR1110] Scanning channel for LoRa transmission ... "));
+
+  // start scanning current channel
+  int state = radio.scanChannel();
+
+  if (state == RADIOLIB_LORA_DETECTED) {
+    // LoRa preamble was detected
+    Serial.println(F("detected!"));
+
+  } else if (state == RADIOLIB_CHANNEL_FREE) {
+    // no preamble was detected, channel is free
+    Serial.println(F("channel is free!"));
+
+  } else {
+    // some other error occurred
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+
+  }
+
+  // wait 100 ms before new scan
+  delay(100);
+}